E-FLITE BLADE CX2 Specifications Download Page 13

Page: 13 / 48

Charge Errors and Indications

In the event that both the red and green LEDs flash, a charge error has occurred. Some examples of

charge errors and their indications include:

•. Alternating.flashing.of.the.red.and.green.LEDs.will.indicate.that.the.charge.process.has.been.interrupted ..If.input.

power.to.the.charger.has.been.interrupted.due.to.disconnection.from.the.power.source.or.a.drop.in.voltage/

current.output.from.the.power.source,.unplug.the.battery.from.the.charger ..Next,.check.to.make.sure.that.the.

input.power.plug.from.the.AC.to.12V.DC.adapter/power.supply.is.connected.or.that.the.alligator.clips.are.firmly.

and.properly.attached.to.the.power.source ..Also.be.sure.that.the.power.source.is.providing.the.proper.amount.of.

voltage.and.current.required.to.the.charger .

After.confirming.the.connections.and.that.the.power.source.is.delivering.the.necessary.voltage.and.current,.re-

start.the.charge.process.by.connecting.the.battery.pack ..Continue.to.monitor.the.charge.process.to.ensure.that.

no.further.charge.errors.occur .

•. Simultaneous.flashing.of.the.red.and.green.LEDs.will.indicate.that.the.voltage.of.the.Li-Po.battery.pack.is.too.low.

to.allow.the.charge.process.to.begin ..In.this.case.the.battery.may.have.been.over-discharged.due.to.flying.the.

model.too.long.(For.more.information.on.preventing.over-discharge.of.the.Li-Po.battery.pack,.see.the.guidelines.

section.found.on.page.9),.or.that.a.single.cell.or.even.all.cells.in.the.battery.pack.may.be.damaged .

If after several charging attempts you continue to see this charge error indication, you should remove

the battery pack from service and replace it with a new one.

If.you.have.any.further.questions.or.concerns.regarding.charge.error.indications,.please.contact.Horizon.Hobby’s.

Product.Support.staff.at.877-504-0233 .

Installing the Transmitter Batteries

Install.the.4.included.“AA”.batteries.in.the.transmitter ..Check.the.power.level.of.the.batteries.and.operation.of.the.

transmitter.by.switching.the.power.switch.on.(upward) ..The.LCD.screen.at.the.top.of.the.transmitter.will.indicate.the.

power.level.of.the.batteries ..If.at.any.time.the.voltage.indicated.on.the.LCD.screen.falls.to.4 .5V.or.less,.an.alarm.

will.sound,.and.it.will.be.necessary.to.replace.the.batteries.with.new.ones .

Note: Because the LPDSM transmitter included with the Blade CX is equipped with Spektrum .GHz

DSM technology, it does not require the same input voltage or current consumption as a typical 7MHz

transmitter for proper operation and optimum performance.

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands