E-FLITE BLADE CX2 Specifications Download Page 19

Page: 19 / 48

If.at.any.time.during.the.test.the.controls.do.not.respond.properly,.double-check.the.servo.reversing.switches.

located.under.the.door.on.the.bottom.left.front.of.the.transmitter ..Dip.switches.5.(THR.channel.reversing),.6.(AIL.

channel.reversing),.7.(ELE.channel.reversing).and.8.(RUD.channel.reversing).should.be.positioned.as.shown.to.

ensure.proper.control.response .

Note: All other dip switches should also be positioned as shown to ensure proper operation. DO NOT

attempt to fly your Blade™ CX with any of the dip switches set in positions that are not shown. The

remaining dip switches may be used for future expansion.

If.the.controls.still.do.not.respond.properly.after.ensuring.that.the.servo.reversing.dip.switch.positions.are.correct,.

you.may.also.check.the.servo.connections.on.the.receiver.side.of.the.4-in-1.unit ..These.should.be.positioned.as.

follows.(when.viewing.the.helicopter.from.behind):

AIL.Channel.–.Forward.aileron.servo

ELE.Channel.–.Rear.elevator.servo

Once.you.have.confirmed.that.the.servo.connection.locations.are.correct,.all.controls.should.be.functioning.

properly ..If.you.do.encounter.any.problems.with.your.Blade.CX2.responding.properly.to.the.transmitter,.do.not.fly ..

Contact.Horizon.Hobby’s.Product.Support.staff.at.877-504-0233 .

If you have confirmed proper control operation of your Blade CX, unplug the flight battery from the

-in-1 unit and reconnect the main motor plugs to the -in-1 unit, taking care to keep the proper

polarity and location of each as they were before the test. Use the label on the -in-1 unit for

reference of the proper polarity and locations. Note that the red wire leads are positive (+) and the

black wire leads are negative (−).

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands