E-FLITE BLADE CX2 Specifications Download Page 34

Page: 34 / 48

Gyro Gain Trimmer Pot Description and Adjustment

The.“gain”.trimmer.pot.adjusts.the.gain.setting.value.of.the.piezo.gyro.used.to.aid.in.keeping.the.tail.of.the.

helicopter.straight/on.heading.during.flight .

Gain Trimmer Pot

•. The.gain.value.is.set.too.high.if.the.tail.of.the.helicopter.twitches/bounces.quickly.from.side.to.side.when.in.

hover ..If.this.is.case.for.your.model,.reduce.the.gyro.gain.in.small.increments.until.the.tail.of.the.helicopter.no.

longer.twitches/bounces.from.side.to.side.in.hover .

Turn the gyro gain trimmer pot counterclockwise (-) to decrease gyro gain.

•. The.gain.value.is.set.too.low.when.the.tail.of.the.helicopter.feels.“loose”.during.flight,.requiring.constant.left.and.

right.rudder.inputs.to.maintain.heading.when.in.hover ..If.this.is.the.case.for.your.model,.increase.the.gyro.gain.in.

small.increments.until.few,.if.any,.left.and.right.rudder.inputs.are.required.to.maintain.heading .

Turn the gyro gain trimmer pot clockwise (+) to increase gyro gain.

Note: When adjusting the gyro gain trimmer pot, the changes will take effect without the need to power

down and re-arm the -in-1 unit. However, please exercise extreme caution when adjusting the gyro

gain trimmer pot with the model armed to prevent personal injury or damage to the model.

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands