E-FLITE BLADE CX2 Specifications Download Page 37

Page: 37 / 48

Channel knob Description and Function

The.transmitter.included.with.your.Blade™.CX2.is.equipped.with.an.optional-use.“Channel.5”.knob.(labeled.as..

“CH.5”).on.the.top.right.panel .

This.knob.allows.you.to.control.function.of.the.transmitter’s.5th.channel ..This.channel.remains.unused.for..

flying.the.Blade.CX2,.however,.it.is.available.for.use.in.controlling.a.variety.of.potential.optional.features..

including.actuation.of.an.additional.servo.or.certain.electronic.components ..It.allows.full.proportional.control..

of.the.5th.channel.from.approximately.0–100%.travel .

The.knob.can.be.operated.in.either.direction.for.control ..You.can.use.either.the.most.clockwise.(+).or.most.

counterclockwise.(-).position.for.0.or.100%.travel,.and.you.will.achieve.approximately.50%.travel.with.the.knob.in.

the.middle.position,.pointing.directly.to.the.rear.of.the.transmitter .

0% Travel

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands