E-FLITE BLADE CX2 Specifications Download Page 10

Page: 10 / 48

Battery Charging

It is important that you only charge the included 7.V 800mAh -cell Li-Po Battery Pack (EFLB0990)

with the included - to -Cell 7.-11.1V Li-Po Balancing Charger (EFLC110). Your battery pack is

equipped with special Charge Protection Circuitry and a Balance Charge Lead with connector that is

only compatible with this charger. Attempting to charge the pack using another Li-Po charger or non

Li-Po compatible charger could result in serious damage. Please familiarize yourself thoroughly with

the warnings and guidelines (pages 8–9) before continuing.

The.included.2-.to.3-Cell.7 .4-11 .1V.Li-Po.Balancing.Charger.will.charge.a.near.fully.discharged.(not.over-discharged).

7 .4V.800mAh.2-cell.Li-Po.Battery.Pack.in.approximately.1 .2–1 .5.hours ..In.some.cases.the.charge.time.may..

be.shorter.depending.on.the.actual.amount.of.capacity.left.in.the.pack.after.a.flight ..

NEVER charge the

battery unattended

Note

:.The.Li-Po.battery.pack.included.with.your.Blade™.CX2.will.arrive.partially.charged ..For.this.reason.the.initial.

charge.may.only.take.approximately.30–50.minutes .

The.charger.requires.up.to.1 .5.amps.of.11 .5-.to.15-Volt.DC.input.power.that.can.be.supplied.by.the.included.AC..

to.12V.DC,.1 .5-Amp.Power.Supply.(EFLC4000).for.convenient.charging.anywhere.an.AC.outlet.is.available ...

NEVER attempt to power the charger from an AC outlet without the use of a proper AC to DC adapter/

power supply

Note

:.When.using.the.AC.to.DC.adapter/power.supply,.the.charger.is.protected.to.prevent.damage.if.the.alligator.

clips.touch ..However,.please.take.care.to.ensure.that.the.alligator.clips.do.not.cause.shorting.of.the.battery,.

adapter/power.supply,.etc ..by.keeping.them.clear .

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands