E-FLITE BLADE CX2 Specifications Download Page 14

Page: 14 / 48

Installing the Flight Battery

Use.the.included.hook.and.loop.material.for.mounting.the.Li-Po.battery.pack ..The.“hook”.material.is.already.installed.

on.the.battery.frame.stop ..The.included.“loop”.material.can.be.installed.on.the.end.of.the.battery.with.or.without.the.

wire.leads,.depending.on.how.you.choose.to.install.the.battery.and.route.the.wire.leads .

If.you.choose.to.install.the.loop.material.on.the.end.of.the.battery.with.the.wire.leads,.it.will.be.a.little.more.difficult.

to.install.the.battery.in.the.model.but.the.wire.leads.can.be.tucked.neatly.inside.of.the.body .

If.you.choose.to.install.the.loop.material.on.the.end.of.the.battery.without.the.wire.leads,.it.will.be.easier.to.install.

the.battery.in.the.model.but.the.power.leads.(red.and.black.leads.with.red.JST.connector).will.need.to.be.placed.

outside.of.the.body .

The.battery.can.be.installed.through.the.opening.in.the.rear.of.the.body ..Be.sure.to.install.the.end.of.the.battery.

with.the.loop.material.first ..If.you.have.installed.the.loop.material.on.the.end.of.the.battery.with.the.wire.leads,.

be.sure.that.the.wire.leads.are.oriented.to.the.left.side.of.the.model.so.that.they.can.pass.by.the.stop ..Slide.the.

battery.into.the.support.frame.until.the.hook.and.loop.material.makes.contact .

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands