E-FLITE BLADE CX2 Specifications Download Page 7

Page: 7 / 48

Preparing for the First Flight Checklist

Please.note.this.checklist.is.not.intended.to.be.a.replacement.for.the.content.included.in.this.instruction..

manual ..Although.it.can.be.used.as.a.quick.start.guide,.we.strongly.suggest.reading.through.this.manual..

completely.before.proceeding .



.. Remove.and.inspect.contents



.. Charge.the.flight.battery



.. Install.the.4.included.“AA”.batteries.in.the.transmitter



. Install.the.flight.battery.in.the.helicopter.(once.it.has.been.fully.charged)



. Check.the.center.of.gravity.of.the.helicopter



. Test.the.controls



. Install.the.optional.Training.Gear.Set.(EFLH1205;.strongly.recommended.if.this.is.your.first.helicopter.model)



. Familiarize.yourself.with.the.controls



. Find.a.suitable.area.for.flying

Flying Checklist

Please.note.this.checklist.is.not.intended.to.be.a.replacement.for.the.content.included.in.this.instruction..

manual ..Although.it.can.be.used.as.a.quick.start.guide,.we.strongly.suggest.reading.through.this.manual..

completely.before.proceeding .



. Always.turn.the.transmitter.on.first



. Plug.the.flight.battery.into.the.4-in-1.control.unit



. Allow.the.4-in-1.control.unit.to.arm.properly



. Fly.the.model



. Land.the.model



. Unplug.the.flight.battery.from.the.4-in-1.control.unit



. Always.turn.the.transmitter.off.last

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands