E-FLITE BLADE CX2 Specifications Download Page 21

Page: 21 / 48

The.following.checklist.contains.the.steps.you.must.follow.to.ensure.proper.arming.and.operation.of.the.4-in-1.unit.

as.well.as.proper.motor.control.response:



Each time before you fly you must ALWAYS turn on the transmitter power first before connecting

the flight battery to the -in-1 unit. Never connect the flight battery to the -in-1 unit before first
powering on the transmitter.

Also, never turn off the transmitter before disconnecting the flight battery from the -in-1 unit first.



Both the throttle (left-hand) stick and throttle trim MUST be in their lowest possible position in order

for the -in-1 unit to arm the electronic speed controls for the main motors.

If.this.is.the.first.test.flight,.or.a.test.flight.following.repairs,.you.will.also.want.to.center.the.rudder,.aileron.and.
elevator.trims .

Throttle Trim

Elevator Trim

Set Throttle

Trim and

Throttle Stick

at Lowest

Position

Rudder

Trim

Aileron

Trim



.. After.confirming.that.the.transmitter.has.been.turned.on.and.has.an.adequate.level.of.battery.power.as.

displayed.by.the.LCD.screen.at.the.top.of.the.transmitter,.it.is.now.safe.to.connect.the.flight.battery.to.the..

4-in-1.unit .

Note: Each time you power the transmitter on, it will enter “Bind Mode” (See pages 9–0 for

more information regarding “Bind Mode”) for a few seconds, as indicated by the red blinking LED

located under the door on the left bottom front of the transmitter. Once this LED becomes solid, the

transmitter is no longer in bind mode. We recommend waiting to connect the flight battery to the

-in-1 unit until after the transmitter has exited bind mode, otherwise the -in-1 unit may not arm

properly or as quickly.

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands