E-FLITE BLADE CX2 Specifications Download Page 36

Page: 36 / 48

Tips Out Of Track —

Adjustment Necessary

Tips In Track —

No Adjustment Necessary

•. If.the.tips.are.not.tracking.in.the.same.plane,.power.the.helicopter.down.to.make.adjustments.to.the.adjustable.

linkage ..You.can.start.by.turning.the.ends.of.the.linkage.in.one-half.to.one-full.turn.at.a.time ..Power.the.helicopter.

up.again.and.re-check.the.blade.tracking .

If.the.tracking.has.gotten.better,.continue.to.turn.the.ends.of.the.linkage.in.one-half.to.one-full.turn.at.a.time.until.

the.tips.are.tracking.in.the.same.plane .

If.the.tracking.has.gotten.worse.after.first.turning.the.ends.of.the.adjustable.linkage.in,.turn.the.ends.of.the.

linkage.back.out.one-half.to.one-full.turn.at.a.time ..If.the.tracking.then.gets.better,.continue.to.turn.the.ends.of.

the.linkage.out.one-half.to.one-full.turn.at.a.time.until.the.tips.are.tracking.in.the.same.plane .

Typically,.not.much.adjustment.should.be.necessary.to.properly.track.the.tips.of.the.upper.main.rotor.blade ..

However,.due.to.the.small.size.of.the.linkage.ends.and.threaded.rods.it.may.not.always.be.possible.to.achieve.

absolutely.perfect.blade.tracking ..Don’t.worry.as.the.helicopter.will.still.perform.well.as.long.as.the.blade.tracking.is.

adjusted.as.closely.as.possible .

Note

:.It.will.not.be.necessary.to.adjust.the.Lower.Main.Rotor.Blade.tracking.as.fixed.links.are.used.between.the.

rotor.blade.and.swashplate .

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands