E-FLITE BLADE CX2 Specifications Download Page 3

Page: 3 / 48

Introduction

The.Blade™.CX2.takes.the.beginner-friendly.flight.stability.of.the.original.Blade.CX.and.adds.Spektrum

.2 .4GHz.

DSM

.radio.control.that.lets.you.fly.anywhere,.anytime.without.ever.having.to.worry.about.interference ..In.fact,.it’s.

the.first.ready-to-fly.RC.aircraft.of.any.kind.to.come.with.this.extraordinary.technology.built.in .

And.best.of.all,.the.Blade.CX2.is.a.truly.Ready-for-Anyone-to-Fly.micro.class.electric.helicopter ..Its.coaxial.counter-

rotating.blades.cancel.out.the.rotational.torque.that.makes.hovering.a.conventional.helicopter.so.difficult.while.

providing.unsurpassed.stability.in.all.other.phases.of.flight.too ..And.whether.you.are.a.first-time.helicopter.pilot.

or.an.experienced.pilot.looking.for.the.best.in.coaxial.micro.helicopter.performance,.you’ll.enjoy.many.of.the.

outstanding.features.that.have.the.Blade.CX2.flying.in.no.time.such.as.factory.installed.main.motors,.4-in-1.control.

unit.with.receiver,.mixer,.ESCs.and.gyro,.and.S60.Super.Sub-Micro.Servos ..With.the.included.5-channel.transmitter,.

2-cell.800mAh.Li-Po.battery.pack,.DC.charger.and.AC.adapter,.you’ll.have.precise.control.for.hovering,.forward.

flight.and.more.with.durations.of.up.to.10–15.minutes.per.charge .

While.the.Blade.CX2.is.nearly.ready-to-fly.right.from.the.box,.please.take.the.time.to.read.through.this.manual.

completely.for.tips.on.battery.safety.and.charging,.control.checks,.flying.and.more ..Please.also.take.a.few.minutes.

to.watch.the.included.Instructional.Video.CD.for.additional.tips.and.to.see.the.Blade.CX2.in.action .

Warning

An.RC.helicopter.is.not.a.toy!.If.misused,.it.can.cause.serious.bodily.harm.and.damage.to.property ..Fly.only.in.open.

areas,.preferably.at.AMA.(Academy.of.Model.Aeronautics).approved.flying.sites,.following.all.instructions .

Keep.loose.items.that.can.get.entangled.in.the.rotor.blades.away.for.the.main.and.tail.blades,.including.loose.

clothing,.or.other.objects.such.as.pencils.and.screwdrivers ..Especially.keep.your.hands.away.from.the.rotor.blades .

Note on Lithium Polymer Batteries

Lithium.Polymer.batteries.are.significantly.more.volatile.than.alkaline.or.Ni-Cd/Ni-MH.batteries.used.in..

RC.applications ..All.manufacturer’s.instructions.and.warnings.must.be.followed.closely ..Mishandling.of..

Li-Po.batteries.can.result.in.fire ..Always.follow.the.manufacturer’s.instructions.when.disposing.of.Lithium.

Polymer.batteries .

Warranty Period

Horizon.Hobby,.Inc .,.(Horizon).warranties.that.the.Products.purchased.(the.“Product”).will.be.free.from.defects.in.

materials.and.workmanship.at.the.date.of.purchase.by.the.Purchaser .

Limited Warranty

(a).This.warranty.is.limited.to.the.original.Purchaser.(“Purchaser”).and.is.not.transferable ..REPAIR.OR.REPLACEMENT.

AS.PROVIDED.UNDER.THIS.WARRANTY.IS.THE.EXCLUSIVE.REMEDY.OF.THE.PURCHASER ..This.warranty.covers.

only.those.Products.purchased.from.an.authorized.Horizon.dealer ..Third.party.transactions.are.not.covered.by.this.

warranty ..Proof.of.purchase.is.required.for.warranty.claims ..Further,.Horizon.reserves.the.right.to.change.or.modify.

this.warranty.without.notice.and.disclaims.all.other.warranties,.express.or.implied .

(b).Limitations-.HORIZON.MAKES.NO.WARRANTY.OR.REPRESENTATION,.EXPRESS.OR.IMPLIED,.ABOUT.NON-

INFRINGEMENT,.MERCHANTABILITY.OR.FITNESS.FOR.A.PARTICULAR.PURPOSE.OF.THE.PRODUCT ..THE.

PURCHASER.ACKNOWLEDGES.THAT.THEY.ALONE.HAVE.DETERMINED.THAT.THE.PRODUCT.WILL.SUITABLY.MEET.

THE.REQUIREMENTS.OF.THE.PURCHASER’S.INTENDED.USE .

(c).Purchaser.Remedy-.Horizon’s.sole.obligation.hereunder.shall.be.that.Horizon.will,.at.its.option,.(i).repair.or.(ii).

replace,.any.Product.determined.by.Horizon.to.be.defective ..In.the.event.of.a.defect,.these.are.the.Purchaser’s.

exclusive.remedies ..Horizon.reserves.the.right.to.inspect.any.and.all.equipment.involved.in.a.warranty.claim ..Repair.

or.replacement.decisions.are.at.the.sole.discretion.of.Horizon ..This.warranty.does.not.cover.cosmetic.damage.or.

damage.due.to.acts.of.God,.accident,.misuse,.abuse,.negligence,.commercial.use,.or.modification.of.or.to.any.

part.of.the.Product ..This.warranty.does.not.cover.damage.due.to.improper.installation,.operation,.maintenance,.or.

attempted.repair.by.anyone.other.than.Horizon ..Return.of.any.goods.by.Purchaser.must.be.approved.by.Horizon.

before.shipment .

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands