E-FLITE BLADE CX2 Specifications Download Page 39

Page: 39 / 48

Transmitter and -in-1 Control Unit Receiver Binding and Fail-Safe

Binding.is.the.process.of.programming.the.receiver.to.recognize.the.GUID.(Globally.Unique.Identifier).code.of.a.

single.specific.transmitter ..If.you.ever.find.that.it.is.necessary.to.replace.your.transmitter.or.the.4-in-1.control.unit.in.

your.model,.it.will.be.necessary.for.you.to.“Bind”.the.new.transmitter.or.4-in-1.control.unit.receiver.to.your.existing.

transmitter.or.receiver.for.proper.operation .

During.the.binding.process,.the.smart.fail-safe.(SmartSafe™).positions.of.your.system.are.also.set ..With.

SmartSafe,.in.case.of.loss.of.signal,.the.throttle.will.go.to.the.preset.position.that.was.stored.during.the.binding.

process.and.all.other.channels.will.hold.their.last.position ..And.if.the.receiver.(4-in-1.Control.Unit).is.powered.on.

before.the.transmitter,.all.channels.but.throttle.will.go.to.the.fail-safe.positions.that.were.stored.during.the.binding.

process,.while.the.throttle.channel.will.not.generate.a.pulse.in.order.to.prevent.the.ESC(s).from.arming .

Note: Because the SmartSafe positions are set during the binding process, it is important to set all

channels to the preferred fail-safe positions before proceeding. In the case of the Blade™ CX, we

strongly recommend setting the throttle stick and throttle trim to their lowest positions, and the rudder,

aileron and elevator channels to their neutral positions. Channel should be set to your preferred

position if you have chosen to utilize it.

The.following.steps.outline.the.binding.process:

•. Each.time.the.transmitter.is.turned.on,.it.enters.“Bind.Mode”.for.a.few.seconds ..You.can.tell.that.the.transmitter.

is.in.bind.mode.when.you.see.the.red.LED.located.under.the.door.on.the.bottom.left.front.of.the.transmitter.blink.

rapidly ..Once.the.LED.becomes.solid,.the.transmitter.is.no.longer.in.bind.mode.and.will.transmit.normally .

LED Location

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands