E-FLITE BLADE CX2 Specifications Download Page 27

Page: 27 / 48

Moving.the.left-hand.stick.to.the.left.will.turn.(yaw).the.nose.of.the.helicopter.to.the.left.about.the.axis.of.the.main.

shaft ..This.is.accomplished.by.increasing.the.speed.of.the.lower.main.rotor.blade.while.decreasing.the.speed.of.the.

upper.main.rotor.blade .

Rudder Trim

Nose Yaws Left

Moving.the.stick.to.the.right.will.turn.(yaw).the.nose.of.the.helicopter.to.the.to.the.right.about.the.axis.of.the.main.

shaft ..This.is.accomplished.by.increasing.the.speed.of.the.upper.main.rotor.blade.while.decreasing.the.speed.of.

the.lower.main.rotor.blade .

Rudder Trim

Nose Yaws Right

The.rudder.trim.can.be.used.to.help.keep.the.nose.of.the.helicopter.from.rotating.to.the.left.or.right.when.in.hover.

with.no.rudder.stick.input ..For.example,.if.the.nose.of.the.helicopter.drifts.to.the.right.when.in.hover,.add.left.rudder.

trim.until.the.nose.stays.as.close.to.straight.as.possible ..Also.note.that.further.adjustments.to.the.rudder.trim.can.

be.made.using.the.Main.Motor.Proportional.Mix.Trimmer.Pot.as.outlined.on.page.32–33 .

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands