manualshive.com logo in svg

E-FLITE BLADE CX2, Specifications

The E-Flite Blade CX2 is a high-performance remote-controlled helicopter perfect for beginners and enthusiasts. With cutting-edge specifications that include a durable construction, stable flight, and easy maneuverability, this product offers an unparalleled flying experience. Enhance your flying skills by downloading the detailed user manual for free from our website manualshive.com, and unlock the full potential of your Blade CX2.

Share
Download
background image

.

With battery power applied, the -in-1 unit status LED will blink red, and then blink green. It is 
extremely important that you do not move or sway the helicopter once the status LED begins to 
blink green confirming that the initialization process and calibration of the gyro has begun

 ..It.is.OK.

to.move.the.model.when.the.status.LED.is.blinking.red.(as.in.the.time.it.takes.to.connect.the.flight.battery.to.
the.4-in-1.unit.and.place.the.model.at.rest),.as.long.as.the.model.remains.motionless.when.the.status.LED.
begins.to.blink.green .

.

When the status LED becomes solid green, the unit is armed and ready for flight

 ..Use.caution.as.both.

main.motors.will.now.run.with.throttle.stick.or.throttle.trim.input ..Do.not.advance.the.throttle.stick.or.trim.until.
you.are.clear.of.the.rotor.blades.and.ready.to.fly .

Note: If the status LED does not become solid green, please review the following:

•. If.after.blinking.red.the.status.LED.becomes.solid.red,.you.have.a.positive.Radio.Frequency.(RF).link.between.

the.transmitter.and.receiver.of.the.4-in-1.unit,.but.the.throttle.stick.and.throttle.trim.may.not.be.in.their.lowest.

possible.positions ..Check.to.be.sure.that.both.the.throttle.stick.and.throttle.trim.are.in.their.lowest.possible.

position.and.the.status.LED.should.blink.green.then.become.solid.green.indicating.the.unit.is.armed.and.ready.for.

flight ..Proceed.to.the.next.step.of.the.checklist.once.the.unit.is.armed .

•. If.after.blinking.red.the.status.LED.continues.to.flash.from.green.to.red,.you.do.not.have.a.positive.RF.link.

between.the.transmitter.and.receiver.of.the.4-in-1.unit ..First,.check.to.be.sure.that.the.transmitter.has.been.

powered.on.and.has.an.adequate.level.of.battery.power ..If.the.transmitter.was.indeed.powered.on,.power.both.

the.transmitter.and.4-in-1.unit.down,.then.follow.the.steps.to.bind.the.4-in-1.unit’s.receiver.to.the.transmitter.(see.

pages.**.to.**.for.more.information) ..Once.you.have.confirmed.that.the.transmitter.and.receiver.are.properly.

bound,.the.4-in-1.unit.should.now.arm.normally .

If.your.4-in-1.unit.will.not.arm.after.following.the.guidelines.as.listed.above,.contact.Horizon.Hobby’s.Product.

Support.staff.at.877-504-0233 .

.

Once you have placed the helicopter in a safe area to test motor control, free from obstructions, 
and are clear of the rotor blades, you can safely begin to power up the model.

. Advance.the.throttle.(left-hand).stick.slowly,.just.until.the.main.rotor.blades.begin.to.spin ..Be.sure.not.to.

advance.the.throttle.stick.too.far.to.keep.the.helicopter.from.lifting.off.the.ground ..Note.the.direction.that.each.
of.the.main.rotor.blades.spins ..When.viewed.from.the.top,.the.lower.main.rotor.blade.should.spin.clockwise.
and.the.upper.main.rotor.blade.should.spin.counterclockwise ..If.either.rotor.blade.is.operating.in.the.wrong.
direction,.unplug.the.battery,.then.simply.reverse.its.motor.plug.polarity.on.the.4-in-1.unit ..Note.that.the.proper.
polarity.is.marked.on.the.label.of.the.4-in-1.unit .

. After.confirming.that.the.direction.of.rotation.for.both.rotor.blades.is.correct,.it.is.best.to.confirm.that.both.

rotor.blades.respond.properly.to.rudder.control.inputs ..With.both.main.rotor.blades.spinning.at.a.low.level.of.
power,.move.the.rudder.(left-hand).stick.all.the.way.to.the.right ..This.should.cause.the.speed.of.the.upper.main.
rotor.blade.to.increase,.and.the.speed.of.the.lower.main.rotor.blade.to.decrease ..Next,.move.the.rudder.stick.
all.the.way.to.the.left ..This.should.cause.the.speed.of.the.lower.main.rotor.blade.to.increase.and.the.speed.
of.the.upper.main.rotor.blade.to.decrease ..If.both.rotor.blades.are.not.responding.properly.to.rudder.input,.
simply.reverse.the.locations.of.their.motor.plugs.on.the.4-in-1.unit ..Note.that.the.proper.motor.plug.locations.
are.marked.on.the.label.of.the.4-in-1.unit .

. After.confirming.both.main.rotor.blades.respond.properly.to.rudder.inputs,.your.Blade™.CX2.is.now.ready..

for.flight ..However,.please.be.sure.to.review.the.following.sections.of.the.manual.before.proceeding.with.the..
first.flight .

Summary of Contents for BLADE CX2

















































Reviews:

No comments

Related manuals for BLADE CX2

Old School Model Works Kaos Construction Manual preview
Kaos
Brand: Old School Model Works Pages: 24
Little Tikes 654039M Assembly Instructions Manual preview
654039M
Brand: Little Tikes Pages: 28
Fisher-Price Laugh & Learn Smart Learning Home Assembly Manual preview
Laugh & Learn Smart Learning Home
Brand: Fisher-Price Pages: 20
LEGO Ninjago 70594 Building Instructions preview
Ninjago 70594
Brand: LEGO Pages: 60
Fisher-Price CMW48 Manual preview
CMW48
Brand: Fisher-Price Pages: 4
Horizon Hobby PRB08032V2 Owner'S Manual preview
PRB08032V2
Brand: Horizon Hobby Pages: 18
M.T.H. Premier 2-4-1A Operator'S Manual preview
Premier 2-4-1A
Brand: M.T.H. Pages: 96
Lionel Scrap Yard Owner'S Manual preview
Scrap Yard
Brand: Lionel Pages: 8
Fisher-Price 77198 Instructions Manual preview
77198
Brand: Fisher-Price Pages: 20
Eduard F-15E exterior Quick Start Manual preview
F-15E exterior
Brand: Eduard Pages: 4
Playskool Bullfrog Bullseye Brochure preview
Bullfrog Bullseye
Brand: Playskool Pages: 1
Fisher-Price R4749 Manual preview
R4749
Brand: Fisher-Price Pages: 24
Faller 222124 Manual preview
222124
Brand: Faller Pages: 4
Hornby CLASS 395 Operating And Maintenance Instructions preview
CLASS 395
Brand: Hornby Pages: 2
marklin 37675 Instruction Manual preview
37675
Brand: marklin Pages: 32
ZAZU Chloe the cat Manual preview
Chloe the cat
Brand: ZAZU Pages: 22
Hacker EDGE 540 RACE 1200 Manual preview
EDGE 540 RACE 1200
Brand: Hacker Pages: 21
esky Honey Bee King II EK1H-E016 Instruction Manual preview
Honey Bee King II EK1H-E016
Brand: esky Pages: 42

Brands by name

Popular brands

Load more brands