E-FLITE BLADE CX2 Specifications Download Page 12

Page: 12 / 48

Once.you.have.connected.the.charger.to.a.power.source.(Use.care.to.ensure.proper.polarity.when.connecting.

the.charger.to.the.power.source),.its.red.LED.will.flash.to.indicate.the.charger.has.power.and.is.ready.to.begin.

charging ..Connect.the.Li-Po.battery.pack.to.the.charger.using.the.specially.marked.Balance.Charge.Lead.exiting.

the.battery.pack.and.the.connector.labeled.with.7 .4V.on.the.charger ..The.connector.is.keyed.to.prevent.reverse.

polarity.connection .

Note: Do not force the connector on the Balance Charge Lead into the connector labeled 11.1V on the

charger. Doing so could result in damage to the battery pack and charger, and could result in a fire.

When.the.battery.is.properly.connected.and.charging.normally,.the.red.and.green.LED.indicators.will.glow.solid ..

Once.the.battery.has.been.fully.charged,.the.green.LED.will.go.out,.leaving.just.the.red.LED.glowing.solid ..The.

battery.can.now.be.removed.from.the.charger.and.installed.into.the.Blade™.CX2.for.flight .

Summary of Contents for BLADE CX2

















































Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands

E-FLITE BLADE CX2, Specifications

Search results

Summary of Contents for BLADE CX2

Reviews:

Related manuals for BLADE CX2

Brands by name

Popular brands