background image

Page 1

Rev 508jf

Pacific Aeromodel Mfg., Inc.

27% Gee Bee “Y” ARF

(A Giant Sport Scale Model)

INSTRUCTION MANUAL

Congratulations on your purchase of this high quality Almost-Ready-to-Fly model airplane kit.  It
has been created by experienced designers and skilled craftsmen and many of its parts have been
factory built for you.  Nevertheless, its ultimate success or failure depends on you. Be sure you have
read and understand this entire manual before attempting to assemble, set up and fly this model
airplane.

This manual is intended for experienced ARF assemblers.  If you have any questions or anything
seems confusing, please contact us for clarification.  Some pictures in this manual may not exactly
match the contents of your kit due to ongoing production improvements.

WARNING - THIS IS NOT A TOY!

Radio controlled model aircraft are capable of inflicting serious injury and/or property damage if not
assembled, operated and maintained in a competent and safe manner.  The successful assembly,
operation and maintenance of radio controlled model aircraft are not intuitive skills and performing
them safely and competently takes experience.  If you are not already an experienced radio
controlled aircraft assembler and flyer, we STRONGLY suggest that you find an experienced
modeler to assist you with the assembly and operation of this model airplane.

Summary of Contents for 27 percentGee Bee "Y" ARF


















Reviews: