manualshive.com logo in svg

DigiDesign Digi 002, Getting Started

Share
Download
DigiDesign Digi 002 Getting Started Download Page 130

Getting Started with Digi 002 & Digi 002 Rack

122

What are the Limitations of 
the Digidesign CoreAudio 
Driver?

The Digidesign CoreAudio Driver has the fol-
lowing limitations:

◆

Pro Tools is not a CoreAudio application and 

therefore requires exclusive access to Digidesign 
hardware. You cannot use CoreAudio applica-
tions and Pro Tools at the same time. To use 
Pro Tools, make sure you quit any CoreAudio 
applications before starting Pro Tools. To use a 
CoreAudio application, make sure you quit 
Pro Tools before starting any CoreAudio appli-
cation.

◆

The Digidesign CoreAudio Driver cannot be 

used to preview sound files from the Finder. 
When a sound file is located in the Mac OS X 
navigation window, a QuickTime transport bar 
is displayed next to it. The QuickTime transport 
bar lets you audition the sound file. The sound 
will always play back though the Macintosh’s 
built-in audio controller (through the Macin-
tosh’s speaker or headphone jack). However, if 
you double-click a sound file, the QuickTime ap-
plication will launch, and can use the Digi-
design CoreAudio Driver for playback. 

◆

The Digidesign CoreAudio Driver cannot be 

used for playback of System Sounds.

Compatibility

This version of Digidesign CoreAudio Driver can 
be used on Digidesign-qualified Pro Tools sys-
tems running on Macintosh, or it can be used as 
a stand-alone driver on Digidesign-qualified 
Macintosh systems that do not have Pro Tools 
installed.

Compatible Software

For a list of CoreAudio Driver-compatible soft-
ware, refer to the Digidesign Web site 
(www.digidesign.com/compato).

Digidesign can only assure compatibility and 
provide support for hardware and software it 
has tested and approved. 

For a list of Digidesign hardware systems, Digi-
design-qualified computers, operating systems, 
and devices, and Digidesign-qualified third-
party CoreAudio-compatible applications, refer 
to the compatibility page of the Digidesign Web 
site (www.digidesign.com/compato).

Installing the Digidesign 
CoreAudio Driver

The CoreAudio Driver is installed by default 
when you install Pro Tools. 

Stand-Alone CoreAudio Driver Installer

This version of Digidesign CoreAudio Driver can 
be installed on Digidesign-qualified Pro Tools 
systems running on Macintosh (for example, if 
the CoreAudio Driver was uninstalled), or it can 
be installed as a stand-alone driver on Macin-
tosh systems that do not have Pro Tools in-
stalled.

For detailed information on installing and 
configuring CoreAudio Driver on systems 
with or without Pro Tools, see the electronic 
pdf of the CoreAudio Usage Guide.

Summary of Contents for Digi 002


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands