Dell PowerEdge UPS 500T Installation And Configuration Manual Download Page 124

Page: 124 / 134

Installation on a VMware ESXi Server

124

VIMA/vMA Shutdown and Startup Configuration

NOTE:

You can configure the physical machine to boot the automatic operating system on startup. This setting is

located in your machine’s basic input/output system (BIOS). For further information, refer to your specific technical

hardware documentation.

NOTE:

You can configure the automatic startup and shutdown properties of guest operating systems as

suspended.

•

Automatic Shutdown of guest (VIMA/vMA) when ESXi host is shutting down and

•

Automatic Startup of guest (VIMA/vMA) when ESXi host is starting

To configure VIMA/vMA shutdowns and startups:

Choose the host server from the left pane tree hierarchy by the Virtual Infrastructure Client interface

and then select the Configuration tab.

Select

Virtual Machine Startup/Shutdown

from the Software list and click

Properties

. The Virtual

Machine Startup and Shutdown window opens (see Figure 123).

Enter the settings as shown on the Virtual Machine Startup and Shutdown window:
• For each virtual machine, set delay startup for 10 seconds
• For each virtual machine, set delay shutdown for 30 seconds

Summary of Contents for PowerEdge UPS 500T







































































































































Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands

Dell PowerEdge UPS 500T, Installation And Configuration Manual

Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands