Dell PowerEdge UPS 500T Installation And Configuration Manual Download Page 134

Page: 134 / 134

Installation on a VMware ESXi Server

134

NOTE:

The VMware ESX and ESXi Server Scripts are from William Lam, VMware vExpert.

http://communities.vmware.com/docs/DOC-9531

Thanks to William Lam (@lamw on Twitter and VMTN) for use of the Scripts.

shutremain

Purpose:

Show or Set message of “Shut down when remaining battery time is below”

Format:

shutremain [-ip target_ip] [-e boolean] [-m time]

Options:

-ip target_ip:

IPv4 or IPv6 address

-e boolean:

true -enable, false -disable

-m time:

minute:second (range 0:0 - 999:59)

NOTE:

No options show relative messages of device.

Example:

shutremain -ip 172.18.127.123 -e true -m 10:10

shutsys

Purpose:

Show or Set message of “System”

Format:

shutsys [-ip target_ip] [-e boolean]

Options:

-ip target_ip:

IPv4 or IPv6 address

-e boolean:

true - enable, false - disable

NOTE:

No options show relative messages of device.

Example:

shutsys -ip 172.18.127.123 -e true

stopsearch

Purpose:

Stop searching thread

Format:

stopsearch

Table 6. Dell CUI Commands (Continued)

Command

Description

Summary of Contents for PowerEdge UPS 500T







































































































































Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands

Dell PowerEdge UPS 500T, Installation And Configuration Manual

Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands