Dell PowerEdge UPS 500T Installation And Configuration Manual Download Page 114

Page: 114 / 134

Installation on a VMware ESX Server

114

Communicating Through the Network Management Card

NOTE:

See Table 6 on page 132 for a complete list of Dell Command User Interface (CUI) commands.

The following procedure is an example of a user entering the settings for a graceful shutdown of selected

devices through the Network Management Card:

Enter the installation path:

/opt/ups

Enter

./CuiManager

to start the CuiManager (see Figure 115).

Search for a single device by entering

search4

and the device network IP address, or search for multiple

devices within a range.
Example command:

search4 -ip 172.18.127.1 -ip 172.18.127.254 -c public

All devices in the network IP address from 172.18.127.1 to 172.18.127.254 are added.

Figure 115. Searching for Devices

Summary of Contents for PowerEdge UPS 500T







































































































































Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands

Dell PowerEdge UPS 500T, Installation And Configuration Manual

Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands