Dell PowerEdge UPS 500T Installation And Configuration Manual Download Page 53

Page: 53 / 134

Configuring the Software

Enter the receiver's e-mail address and click

to save and exit.

Dell recommends testing the e-mail function by selecting the e-mail address and clicking

Test

. The

software sends a test e-mail to the specified recipient.

NOTE:

You can select the event messages from the E-Mail Settings window or from the Event Action window.

Verify that one or more recipient e-mail addresses are selected, and then select the event messages to

be sent by selecting the message check box (see Figure 54).

Figure 54. E-Mail Recipient and Message Selection

If the selected event occurs, the software sends the e-mail to all of the selected addresses in the

Receiver E-Mail list.

Summary of Contents for PowerEdge UPS 500T







































































































































Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands

Dell PowerEdge UPS 500T, Installation And Configuration Manual

Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands