Dell PowerEdge UPS 500T Installation And Configuration Manual Download Page 94

Page: 94 / 134

Configuring the Software

To change the SNMP port if the default Port 162 is occupied by other programs:

Select

SNMP Port Setting

from the

SNMP

menu.

Enter the new SNMP port and click

(see Figure 103). The port range of the SNMP Port Settings is

1 to 65535, and the new port is immediately enabled.

Figure 103. SNMP Port Settings Confirmation Window

Rebooting Computers after a Utility Failure

You can reboot individual computers or all computers on the LAN automatically after a utility power

failure.
To configure the computers to reboot when the utility power restores:

Select

Wake Up

from the

UPS

menu to open the Wake on LAN window (see Figure 104).

Figure 104. Wake on LAN Window

Summary of Contents for PowerEdge UPS 500T







































































































































Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands

Dell PowerEdge UPS 500T, Installation And Configuration Manual

Search results

Summary of Contents for PowerEdge UPS 500T

Reviews:

Related manuals for PowerEdge UPS 500T

Brands by name

Popular brands