background image

Memory Module(s)

25

6

Memory Module(s)

 

WARNING: 

Before working inside your computer, read the safety information 

that shipped with your computer. For additional safety best practices information, 
see the Regulatory Compliance Homepage at 
www.dell.com/regulatory_compliance.

 

CAUTION: 

To avoid electrostatic discharge, ground yourself by using a wrist 

grounding strap or by periodically touching an unpainted metal surface (such as a 
connector on your computer).

 

CAUTION: 

Only a certified service technician should perform repairs on your 

computer. Damage due to servicing that is not authorized by Dell is not covered by 
your warranty.

 

CAUTION: 

To help prevent damage to the system board, remove the main battery 

(see "Removing the Battery Pack" on page 13) before working inside the computer. 

You can increase your computer memory by installing memory modules on 

the system board. See the "Specifications" section in your 

Mobile Manual 

for 

information on the type of memory supported by your computer.

 

NOTE: 

Memory modules purchased from Dell or Alienware are covered under your 

computer warranty.

 

NOTE: 

If you purchased a dual-core processor, your computer supports only 

memory module connectors DIMM 1 and DIMM 2.

 

NOTE: 

Your computer supports up to four memory module connectors. You can 

access connectors DIMM 1 and DIMM 2 by removing the compartment door at the 

bottom of your computer. You can access connectors DIMM 3 and DIMM 4 by 

removing the memory-module cover on top of the palm rest assembly.

Removing the Memory Module(s)

1

Follow the instructions in "Before You Begin" on page 9. 

2

Remove the battery pack (see "Removing the Battery Pack" on page 13).

3

Remove the compartment door (see "Removing the Compartment Door" 

on page 15).

Summary of Contents for Alienware M17X R3















































































































Reviews: