Dell Alienware M17X R3 Service Manual Download Page 22

Page: 22 / 110

Hard Drive(s)

CAUTION:

When the hard drive is not in the computer, store it in protective

antistatic packaging (see "Protecting Against Electrostatic Discharge" in the
safety instructions that shipped with your computer).

Replacing the Hard Drive(s)

Follow the instructions in "Before You Begin" on page 9.

Remove the new drive from its packaging.
Save the original packaging for storing or shipping the hard drive.

Connect the interposer to the hard drive.

Place the hard drive in the hard-drive bracket.

Replace the four screws that secure the hard drive to the hard-drive

bracket.

Align the connector on the hard drive with the connector on the system

board and press the hard drive until it is fully seated.

interposer

screws (4)

hard-drive bracket

hard drive

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands