Dell Alienware M17X R3 Service Manual Download Page 61

Page: 61 / 110

Wireless Mini-Card

CAUTION:

When the Mini-Card is not in the computer, store it in protective

antistatic packaging. For more information, see "Protecting Against Electrostatic
Discharge" in the safety information that shipped with your computer.

Replacing the Mini-Card

Follow the instructions in "Before You Begin" on page 9.

Remove the new Mini-Card from its packaging.

CAUTION:

Use firm and even pressure to slide the card into place. If you use

excessive force, you may damage the connector.

CAUTION:

The connectors are keyed to ensure correct insertion. If you feel

resistance, check the connectors on the card and on the system board, and realign
the card.

Insert the Mini-Card connector at a 45-degree angle into the connector on

the system board.

Press the other end of the Mini-Card down into the slot on the system

board and replace the screw that secures the Mini-Card to the system

board.

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands