Dell Alienware M17X R3 Service Manual Download Page 104

Page: 104 / 110

104

System Setup

Integrated Network

Allows you to enable or disable the on-

board LAN controller.

• Disabled: Internal LAN is

disabled and is not visible to the

operating system.

• Enabled: Internal LAN is

enabled.

High Definition Audio

Allows you to enable or disable the

internal high definition audio device.

• Disabled: The internal audio

device is disabled and is not

visible to the operating system.

• Enabled: The internal audio

device is enabled.

SD Card Reader

Allows you to enable or disable the

internal SD card reader.

CPU Turbo Mode

Allows you to enable or disable the Intel

CPU turbo mode performance option.

Performance Options

Allows you to configure fields in the

Performance Options sub-menu (for more

information, see "Advanced Menu—

Performance Options" on page 105.

SATA Operation

Allows you to configure the operating

mode of the integrated SATA hard drive

controller.

• AHCI: SATA is configured for

AHCI mode.

• RAID: STAT is configured for

RAID mode.

SATA HARD DRIVE 1

Displays the installed primary SATA hard

drive model.

SATA HARD DRIVE 2

Displays the installed secondary SATA

hard drive model.

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands