manualshive.com logo in svg

Dell Alienware M17X R3, Service Manual, Page: 36 / 110

Share
Download
Dell Alienware M17X R3 Service Manual Download Page 36

36

Graphics-Card Assembly

 

Replacing the Graphics-Card Assembly

1

Follow the instructions in "Before You Begin" on page 9.

2

Insert the graphics card connector at a 45-degree angle into the connector 

on the system board.

3

Press the other end of the graphics-card assembly down into the slot on the 

system board and replace the two screws that secure the graphics-card 

assembly to the system board.

4

Replace the graphics-card heat sink fan (see "Replacing the Graphics-Card 

Heat Sink Fan" on page 32).

5

Replace the compartment door (see "Replacing the Compartment Door" 

on page 16).

6

Replace the battery pack (see "Replacing the Battery Pack" on page 14).

 

CAUTION: 

Before turning on the computer, replace all screws and ensure that no 

stray screws remain inside the computer. Failure to do so may result in damage to 
the computer.

1

graphics-card assembly

2

screws (2)

1

2

Summary of Contents for Alienware M17X R3















































































































Reviews:

No comments