Dell Alienware M17X R3 Service Manual Download Page 46

Page: 46 / 110

Processor Module

CAUTION:

To ensure maximum cooling for the processor module, do not touch the

heat transfer areas on the processor thermal cooling assembly. The oils in your
skin can reduce the heat transfer capability of the thermal pads.

CAUTION:

When removing the processor module, lift the module straight up. Be

careful not to bend the pins on the processor module.

Lift the processor module from the ZIF socket.

Replacing the Processor Module

NOTE:

If a new processor module is installed, you will receive a new

thermal-cooling assembly, which will include an affixed thermal pad, or you will

receive a new thermal pad along with documentation to illustrate proper

installation.

Follow the instructions in "Before You Begin" on page 9.

ZIF socket

ZIF-socket cam screw

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands