Dell Alienware M17X R3 Service Manual Download Page 81

Page: 81 / 110

Palm Rest Assembly

Carefully pry out the palm rest assembly along the rear edge and then ease

the palm rest assembly from the computer base.

CAUTION:

Carefully separate the palm rest assembly from the computer base to

avoid damage to the palm rest assembly.

Lift the palm rest assembly off the computer base.

Replacing the Palm Rest Assembly

Follow the instructions in "Before You Begin" on page 9.

Align the screw holes on the palm rest assembly with the screw holes on

the computer base.

Replace the three screws that secure the palm rest assembly to the

computer base.

palm rest assembly

LVDS cable

touch pad cable

Media Card Reader cable

screws (3)

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands