Dell Alienware M17X R3 Service Manual Download Page 68

Page: 68 / 110

Power Button Board

Replacing the Power Button Board

Follow the instructions in "Before You Begin" on page 9.

Align the slots on the power button board with the alignment posts on the

chassis and secure the power button board in place.

Replace the two screws that secure the power button board to the palm

rest assembly.

Connect the power button board cable to the connector on the system

board.

Replace the keyboard (see "Replacing the Keyboard" on page 57).

Replace the center control cover (see "Replacing the Center Control

Cover" on page 52).

Replace the compartment door (see "Replacing the Compartment Door"

on page 16).

Replace the battery pack (see "Replacing the Battery Pack" on page 14).

screws (2)

power button board

power button board cable

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands