Dell Alienware M17X R3 Service Manual Download Page 97

Page: 97 / 110

System Board

Replacing the System Board

Follow the instructions in "Before You Begin" on page 9.

Align the connectors on the system board with the slots on the computer

base and place it on the computer base.

Replace the six screws that secure the system board to the computer base.

Follow the instructions from step 4 to step 6 in "Replacing the Optical

Drive" on page 94.

Replace the speakers (see "Replacing the Speakers" on page 88).

Replace the Bluetooth card (see "Replacing the Bluetooth Card" on

page 84).

Replace the palm rest assembly (see "Replacing the Palm Rest Assembly"

on page 81).

Replace the status light board (see "Replacing the Status Light Board" on

page 76).

screws (6)

system board

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands