Dell Alienware M17X R3 Service Manual Download Page 88

Page: 88 / 110

Speakers

Disconnect the speakers cable from the connector on the system board.

Note the speakers cable routing and remove the cable from the routing

guides on the computer base.

Remove the four screws that secure the speakers to the computer base.

Lift the speakers along with the cable off the computer base.

Replacing the Speakers

Follow the instructions in "Before You Begin" on page 9.

Align the screw holes on the speakers with the screw holes on the computer

base and route the speaker cables in the routing guides.

Replace the four screws that secure the speakers to the computer base.

Route the speakers cable through the routing guides on the computer

base.

speakers (2)

screws (4)

speakers cable

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands