manualshive.com logo in svg

Dell Alienware M17X R3, Service Manual, Page: 32 / 110

Share
Download
Dell Alienware M17X R3 Service Manual Download Page 32

32

Graphics-Card Heat Sink Fan

Replacing the Graphics-Card Heat Sink Fan

1

Follow the instructions in "Before You Begin" on page 9.

2

Align the screw holes on the graphics-card heat sink fan with the screw 

holes on the chassis.

3

Tighten the three captive screws that secure the graphics-card heat sink 

fan to the chassis.

4

Connect the graphics-card heat sink fan cable to the connector on the 

system board. 

5

Replace the compartment door (see "Replacing the Compartment Door" 

on page 16).

6

Replace the battery pack (see "Replacing the Battery Pack" on page 14).

 

CAUTION: 

Before turning on the computer, replace all screws and ensure that no 

stray screws remain inside the computer. Failure to do so may result in damage to 
the computer.

1

graphics-card heat sink fan cable

2

captive screws (3)

3

graphics-card heat sink fan

1

2

3

Summary of Contents for Alienware M17X R3















































































































Reviews:

No comments