Dell Alienware M17X R3 Service Manual Download Page 106

Page: 106 / 110

106

System Setup

Memory Override Support

Allows you to enable or disable the

memory override option support.

• Disabled: The memory override support

is disabled.

• Enabled: Displays additional memory

override support options.

Memory Voltage

Allows you to increase memory voltage.

Memory Frequency

Allows you to set memory frequency.

DIMM Profile (XMP)

Allows you to configure different XMP

options.

Wireless Menu

Bluetooth

Allows you to enable or disable the

internal Bluetooth device.

• Disabled: The internal Bluetooth

device is disabled and is not

visible to the operating system.

• Enabled: The internal Bluetooth

device is enabled.

Wireless Network

Allows you to enable or disable the

internal wireless device.

• Disabled: The internal wireless

device is disabled and is not

visible to the operating system.

• Enabled: The internal wireless

device is enabled.

DMC

Allows you to enable or disable the

internal DMC device.

Wireless Switch/Hotkey

Allows you to disable all internal wireless

devices.

Security Menu

Supervisor Password

Displays if the supervisor password is clear

or set.

Summary of Contents for Alienware M17X R3















































































































Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands

Dell Alienware M17X R3, Service Manual

Search results

Summary of Contents for Alienware M17X R3

Reviews:

Related manuals for Alienware M17X R3

Brands by name

Popular brands