Dell Alienware Aurora R4 Owner'S Manual Download Page 129

Page: 129 / 162

Front Bezel

129

Front Bezel

WARNING:

Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on
page 13. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.

Prerequisites

Remove the left side-panel. See "Removing the Left Side-Panel" on

page 25.

Open the PCI shroud. See "Opening the PCI Shroud" on page 45.

Remove the drive-bay shroud. See "Removing the Drive-Bay Shroud" on

page 47.

Remove the right-side top panel. See "Removing the Right-Side Top

Panel" on page 107.

Remove the right lighting-board. See "Removing the Right Lighting-

Board" on page 117.

Remove the right-side middle panel. See "Removing the Right-Side

Middle Panel" on page 113.

Remove the right-side bottom panel. See "Removing the Right-Side

Bottom Panel" on page 121.

Removing the Front Bezel

Remove the screws that secure the front bezel to the chassis.

Note the routing of the front-bezel cables and disconnect the front bezel

cables from the connectors on the master I/O board.

book.book Page 129 Wednesday, May 16, 2012 2:37 PM

Summary of Contents for Alienware Aurora R4



































































































































































Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands

Dell Alienware Aurora R4, Owner'S Manual

Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands