Dell Alienware Aurora R4 Owner'S Manual Download Page 152

Page: 152 / 162

152

System Setup Utility

Boot Sequence

This feature allows you to change the boot sequence for devices.

Boot Options

•

Diskette Drive

—

The computer attempts to boot from the floppy disk

drive. If no operating system is on the drive, the computer generates an

error message.

•

Hard Drive

— The computer attempts to boot from the primary hard

drive. If no operating system is on the drive, the computer generates an

error message.

User Password:

Allows you to change the user password.

You cannot use the user password to enter

the BIOS setup, during POST.

Set Supervisor Password

Allows you to set a supervisor password.

Boot

Set Boot Priority

1st Boot Device

Displays the first boot device.

2nd Boot Device

Displays the second boot device.

3rd Boot Device

Displays the third boot device.

4th Boot Device

Displays the fourth boot device.

5th Boot Device

Displays the fifth boot device.

6th Boot Device

Displays the sixth boot device.

7th Boot Device

Displays the seventh boot device.

Hard Disk Drive BBS

Priorities

Sets the hard drive boot priority. The

items displayed are dynamically updated

according to the hard drives detected.

CD/DVD ROM Drive BBS

Priorities

Sets the CD/DVD drive boot priority.

Exit

Provides options to

Save Changes and Reset

Discard Changes

and Reset

, and

Restore Defaults

book.book Page 152 Wednesday, May 16, 2012 2:37 PM

Summary of Contents for Alienware Aurora R4



































































































































































Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands

Dell Alienware Aurora R4, Owner'S Manual

Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands