Dell Alienware Aurora R4 Owner'S Manual Download

Page: 49 / 162

PCI-Express x1 Card

PCI-Express x1 Card

WARNING:

Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on
page 13. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.

Prerequisites

Remove the left side-panel. See "Removing the Left Side-Panel" on

page 25.

Open the PCI shroud. See "Opening the PCI Shroud" on page 45.

Removing the PCI-Express x1 Card

Locate the PCI-Express x1 card on the system board. See "System-Board

Components" on page 20.

Disconnect any cables connected to the card (if applicable).

Remove the screw that secures the card to the chassis.

Grasp the card by its top corners and ease it out of the connector.

NOTE:

For removing a PCI-Express x16 card, see "Removing the Graphics Card" on

page 57.

NOTE:

If you are not replacing a card, install a filler bracket in the empty card-slot

opening.

book.book Page 49 Wednesday, May 16, 2012 2:37 PM

Summary of Contents for Alienware Aurora R4



































































































































































Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands

Dell Alienware Aurora R4, Owner'S Manual

Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands