Dell Alienware Aurora R4 Owner'S Manual Download Page 113

Page: 113 / 162

Right-Side Middle Panel

113

Right-Side Middle Panel

WARNING:

Before working inside your computer, read the safety information

that shipped with your computer and follow the steps in "Before You Begin" on
page 13. For additional safety best practices information, see the Regulatory
Compliance Homepage at dell.com/regulatory_compliance.

Prerequisites

Remove the left side-panel. See "Removing the Left Side-Panel" on

page 25.

Open the PCI shroud. See "Opening the PCI Shroud" on page 45.

Remove the drive-bay shroud. See "Follow the steps in "After Working

Inside Your Computer" on page 15." on page 46.

Remove the right-side top panel. See "Removing the Right-Side Middle

Panel" on page 113.

Remove the right lighting-board. See "Removing the Right Lighting-

Board" on page 117.

Removing the Right-Side Middle Panel

Remove the screws that secure the right-side middle panel to the chassis.

Lift the right-side middle panel up and away from the chassis.

book.book Page 113 Wednesday, May 16, 2012 2:37 PM

Summary of Contents for Alienware Aurora R4



































































































































































Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands

Dell Alienware Aurora R4, Owner'S Manual

Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands