Dell Alienware Aurora R4 Owner'S Manual Download

Page: 59 / 162

Graphics Card

Connect the power cables to the graphics card.

Postrequisites

Close the PCI shroud. See "Closing the PCI Shroud" on page 46.

Replace the left side-panel. See "Replacing the Left Side-Panel" on

page 27.

Follow the steps in "After Working Inside Your Computer" on page 15.

Installing Dual Graphic Cards

Locate the second PCI-Express x16 connector on the system board. See

"System-Board Components" on page 20.

Align the second graphics card with the second PCI-Express x16 card

connector on the system board.

Place the card in the connector and press down firmly. Ensure that the card

is firmly seated in the slot.

Replace the screws that secure the second graphics card to the chassis.

Connect the dual graphics bridge connecting the two graphics card.

Connect the two power cables to the graphics card.

book.book Page 59 Wednesday, May 16, 2012 2:37 PM

Summary of Contents for Alienware Aurora R4



































































































































































Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands

Dell Alienware Aurora R4, Owner'S Manual

Search results

Summary of Contents for Alienware Aurora R4

Reviews:

Related manuals for Alienware Aurora R4

Brands by name

Popular brands