manualshive.com logo in svg

Daikin FTKD50BVM, Service Manual

Share
Download
Daikin FTKD50BVM Service Manual Download Page 138

Si04-306

Check

Service Diagnosis

129

5.1.5

Installation Condition Check

Check No.7

Installation condition check

Normal

Change the position of the air 
discharge grille or the 
installation location.

Change the position of the air 
discharge grille or the 
installation location.

Clean the heat exchanger.

Change the installation 
location or direction.

Check the outside air 
temperature (temperature of air 
taken in by the outdoor unit).  
(The outside air temperature 
shall be 43˚C or lower.)

Check 

the allowable

dimensions of the air suction

and discharge

area.

Is

the air flow

blocked by obstacles or

winds blowing in the

opposite direction?

(R1438)

Abnormal

YES

YES

YES

Does

the discharged

air from other outdoor

unit cause an increase of

the suction air

temperature?

NO

NO

NO

Is the heat exchanger

very dirty?

Summary of Contents for FTKD50BVM



















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands