manualshive.com logo in svg

Daikin FTKD50BVM, Service Manual

Share
Download
Daikin FTKD50BVM Service Manual Download Page 116

Si04-306

Troubleshooting

Service Diagnosis

107

Troubleshooting

Check No.5

Refer to P.127

Check No.6

Refer to P.128

Check No.11

Refer to P.131

Correct.

Reconnect.

Replace the four way valve 
coil.

Replace the outdoor unit 
PCB.

Reconnect in position.

Replace a defective 
thermistor.

Refer to the refrigerant line 
check procedure.

Replace the four way valve 
(defective or dust-clogged).

(R2845)

Caution

Be sure to turn off power switch before connect or disconnect connector, 
or parts damage may be occurred.

Four way valve coil 

disconnected (loose)?

YES

YES

NO

Functioning     

NO

Check No. 11

Check the refrigerant line.

Malfunctioning     

l

 Insufficient gas

l

 Water mixed

l

 Stop valve defective 

Harness out of connector?

NO

YES

Disconnect the

 harness from 

the connector. 

Resistance between 

harnesses about 

1500 ohms?

Malfunctioning  

Functioning

Check No. 5

Check the four way valve 

switching output.

YES

NO  

Any thermistor disconnected?

Malfunctioning  

Functioning  

Check No. 6

Check the thermistors.

Check the continuity of the four 
way valve coil and harness.

Summary of Contents for FTKD50BVM



















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands