Daikin FTKD50BVM Service Manual Download Page 112

Page: 112 / 210

Si04-306

Troubleshooting

Service Diagnosis

103

4.9

DC Fan Lock

Remote
Controller
Display

Method of
Malfunction
Detection

A fan motor or related error is detected by checking the high-voltage fan motor rpm being
detected by the hall IC.

Malfunction
Decision
Conditions

The fan does not start in 30 seconds even when the fan motor is running.

The system will be shut down if the error occurs 16 times.

Clearing condition: Continuous run for about 5 minutes (normal)

Supposed
Causes

Fan motor breakdown

Harness or connector disconnected between fan motor and PCB or in poor contact

Foreign matters stuck in the fan

Troubleshooting

Check No.15

Refer to P.133

Turn off the power and
reconnect the connector.

Remove.

Replace the outdoor unit
fan motor.

Replace the outdoor unit
PCB.

(R2843)

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

Fan motor connector

disconnected?

YES

Pulse signal inputted?

Foreign matters in or

around the fan?

Get started.

Check No. 15

Check the outdoor unit PCB rpm
pulse input.

Summary of Contents for FTKD50BVM



















































































































































































































Search results

Summary of Contents for FTKD50BVM

Reviews:

Brands by name

Popular brands

Daikin FTKD50BVM, Service Manual

Search results

Summary of Contents for FTKD50BVM

Reviews:

Brands by name

Popular brands