Daikin FTKD50BVM Service Manual Download Page 122

Page: 122 / 210

Si04-306

Troubleshooting

Service Diagnosis

113

Troubleshooting

Check No.6

Refer to P.128

Radiation fin thermistor

Discharge pipe thermistor

Outdoor

heat exchanger thermistor

Outdoor air thermistor

Turn on the power again.

Reconnect.

Replace defective one(s) of
the following thermistors.

Radiation fin thermistor

Discharge pipe

temperature thermistor

Outdoor unit heat

exchanger temperature
thermistor

Outdoor air thermistor

Replace the following
thermistor.

Indoor unit heat

exchanger thermistor

Replace the outdoor unit
PCB. (Replace the indoor
unit PCB.)

(R2849)

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

Error displayed again

on remote controller?

YES

Indoor unit

heat exchanger thermistor

functioning?

Connector or thermistor

disconnected?

YES

Normal?

Check No. 6

Check the thermistor resistance
value.

Check No. 6

Check the indoor unit heat
exchanger thermistor resistance
value in the heating mode.

Summary of Contents for FTKD50BVM



















































































































































































































Search results

Summary of Contents for FTKD50BVM

Reviews:

Brands by name

Popular brands

Daikin FTKD50BVM, Service Manual

Search results

Summary of Contents for FTKD50BVM

Reviews:

Brands by name

Popular brands