Daikin FTKD50BVM Service Manual Download Page 126

Page: 126 / 210

Si04-306

Troubleshooting

Service Diagnosis

117

Troubleshooting

Check No.6

Refer to P.128

Check No.7

Refer to P.129

Check No.9

Refer to P.130

Turn off the power and turn it on
again to get the system started.

Check No. 6

Check the thermistor resistance
value.

Replace the fin thermistor.

Check the power transistor
and fin for looseness. If
they are found to be fit
tightly, replace the PCB or
the power transistor.

Replace the fan motor.
Correct the connectors and
fan motor leads.
Replace the outdoor unit
PCB.

Clean up the radiation fin.

(R2851)

Caution

Be sure to turn off power switch before connect or disconnect connector,
or parts damage may be occurred.

Error displayed again?

YES

Slightly dirty

Check No. 9

Check the outdoor unit

fan or related.

Malfunctioning

Radiation fin dirty?

Too dirty

Functioning

Thermistor as

specified in its characteristic

chart?

Above 90˚C?

YES

Fin thermistor

Check the radiation fin
temperature.

Check No. 7

Check the installation condition.

Summary of Contents for FTKD50BVM



















































































































































































































Search results

Summary of Contents for FTKD50BVM

Reviews:

Brands by name

Popular brands

Daikin FTKD50BVM, Service Manual

Search results

Summary of Contents for FTKD50BVM

Reviews:

Brands by name

Popular brands