manualshive.com logo in svg

Daikin FTKD50BVM, Service Manual

Share
Download
Daikin FTKD50BVM Service Manual Download Page 124

Si04-306

Troubleshooting

Service Diagnosis

115

Troubleshooting

Check No.6

Refer to P.128

Check No.7

Refer to P.129

Check No.9

Refer to P.130

Turn off the power and turn it on 
again.

Check No. 6

Check the thermistor resistance 
value.

Replace the fin thermistor.

Replace the outdoor unit 
PCB.

Replace the fan motor.
Correct the connectors and 
fan motor leads.
Replace the outdoor unit 
PCB.

Clean up the radiation fin.

(R2850)

Caution

Be sure to turn off power switch before connect or disconnect connector, 
or parts damage may be occurred.

Error again or outdoor unit 

fan activated?

YES

l

 Fin thermistor

NO

Slightly dirty   

Check No. 9

Check the outdoor unit 

fan or related.

Malfunctioning

Radiation fin dirty?

Too dirty   

Functioning

Thermistor as 

specified in its characteristic

chart?

Above 80˚C?

NO

YES

NO

YES

Check the radiation fin 
temperature.

Check No. 7

Check the installation condition.

WARNING

To cool down the electricals, the 
outdoor unit fan gets started when 
the radiation fin temperature rises 
above 78˚C and stops itself when 
it drops below 70˚C.

Summary of Contents for FTKD50BVM



















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands