Daikin BPMK928B42 Service Manual Download Page 182 | Manualshive

Page: 182 / 410

background image

Si18-201

System control

Main Functions

169

3.40

Protection Control of SkyAir Indoor Units

SkyAir Indoor
Unit Peak-Cut
Zone

The zones for SkyAir indoor unit peak-cut control is produced in the BP unit.

Peak-cut control
Based on the heat exchanger temperature information sent from the indoor unit, the zones are
produced to prevent abnormal rise of the high pressure.

Freeze-up prevention control
Based on the freeze-up prevention status information sent from the BP unit (indoor unit), the
zones are produced to prevent freezing-up of the indoor heat exchanger.

Even if the stop zone is reached, the zone remains as the drooping zone for 540 sec.

DCPC5 : 68˚C

DCPC4 : 56˚C

DCPC3 : 54˚C

DCPC2 : 52˚C

DCPC1 : 50˚C

Stop zone

Drooping zone

No-change zone

Increasing zone

Reset zone

(M1053)

Stop zone

Drooping zone

No-change zone

Increase zone

Reset zone

DCTO1 : 11˚C

DCTO2 : 7˚C

DCTO3 : 4˚C

DCTO4 : 2˚C

DCTO5 : 0˚C

(M1054)

«
...
180
181
182
183
184
...
»

Summary of Contents for BPMK928B42



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for BPMK928B42

Brand: Jandy Pages: 96

Brand: Daewoo Pages: 9

Brand: DAB Pages: 64

Brand: York Pages: 90

Brand: Barracuda PUMPS Pages: 4

Brand: Becker Pages: 5

Brand: Zibro Pages: 75

Tranquility TR Series

Brand: ClimateMaster Pages: 96

Brand: Yardworks Pages: 19

Brand: SAMES KREMLIN Pages: 49

Brand: Wayne Pages: 12

Brand: vacuubrand Pages: 96

Brand: Campbell Hausfeld Pages: 4

Brand: Quality Pages: 11

Brand: Thermablaster Pages: 16

Brand: Bristan Pages: 20

WHISPA III 5000 WM

Brand: Myson Pages: 16

Brand: Dantherm Pages: 135

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands