Daikin BPMK928B42 Service Manual Download Page 347

Page: 347 / 410

Outdoor Unit

Si18-201

334

Removal Procedure

2.6

Removal of Sound Insulation

Procedure

Warning Be sure to wait 10 minutes or more after turning off all power supplies

before disassembling work.

Step

Procedure

Points

Remove the terminal
cover and disconnect the
compressor leads,
referring to the
instructions in "Removal
of PCB".

1. Disconnecting the

peripheral components

Detach the compressor
mounting plate.

Slide up the cover at
the back of the partition
board. Release the
cover off the two
hooks.

The partition board cannot
be detached.

Remove the screw
from the partition
board.

Open the partition
board to the left to
easily access the
sound insulation.

2. Detaching the sound

insulation

Undo the sound
insulation fixture string.

Draw out the sound
insulation cover and
sound insulation from
the top of the
compressor.

Summary of Contents for BPMK928B42



























































































































































































































































































































































































































Search results

Summary of Contents for BPMK928B42

Reviews:

Related manuals for BPMK928B42

Brands by name

Popular brands

Daikin BPMK928B42, Service Manual

Search results

Summary of Contents for BPMK928B42

Reviews:

Related manuals for BPMK928B42

Brands by name

Popular brands