D-Link xStack, Reference Manual

Page: 1007 / 1284

xStack® DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch CLI Reference Guide
1002
Parameters
<profile_id> - Specifies the profile ID number to be configured.
add - Specifies to add a tag for the assigned S-VLAN before the Outer-VLAN tag. If there is an S-
TAG in the packet, this rule will not take effect.
rule_id - Specifies the rule ID to be added to the profile. If the rule ID is not specified, it will be
assigned automatically.
<rule_id> - Enter the rule ID used here.
add - Specifies to add a tag for the assigned S-VLAN before the Outer-VLAN tag. If there is an S-
TAG in the packet, this rule will not take effect.
svid - Specifies the S-VLAN ID to be assigned to the matched packet.
<vlanid 1-4094> - Enter the S-VLAN ID used here. This value must be between 1 and 4094.
priority - Specifies to assign the 802.1p priority of the S-Tag. If the priority is not specified, the
802.1p priority of S-Tag will be assigned by the default procedure.
<priority 0-7> - Enter the 802.1p priority value here. This value must be between 0 and 7.
classify - Specifies the classification.
source_mac - Specifies the source MAC address or MAC address range for the match.
<macaddr> - Enter the source MAC address or range here.
sa_mask - Specifies the source MAC address mask.
<macmask> - Enter the source MAC address mask here.
destination_mac - Specifies the destination MAC address or MAC address range for the match.
<macaddr> - Enter the destination MAC address or range here.
da_mask - Specifies the destination MAC address mask.
<macmask> - Enter the destination MAc address mask here.
source_ipv4 - Specifies the source IPv4 address or IPv4 subnet for the match.
<ipaddr> - Enter the source IPv4 address or subnet here.
sip_mask - Specifies the source IPv4 address mask used.
<netmask> - Enter the source IPv4 address mask used here.
destination_ipv4 - Specifies the destination IPv4 address or IPv4 subnet for the match.
<ipaddr> - Enter the destination IPv4 address or subnet here.
dip_mask - Specifies the destination IPv4 address mask used.
<netmask> - Enter the destination IPv4 address mask used here.
outer_vid - Specifies the packet’s outer-VID for the match.
<vidlist> - Enter the packet's outer-VID used here.
802.1p - Specifies the packet’s 802.1p priority for the match.
<priority 0-7> - Enter the packet's 802.1p priority value used here. This value must be
between 0 and 7.
ip_protocol - Specifies that the IP protocol will be used.
<value 0-255> - Enter the IP protocol value used here. This value must be between 0 and
255.
l4_src_port - Specifies the Layer 4 source port ID for the match.
<value 1-65535> - Enter the Layer 4 source port ID used here. This value must be between 1
and 65535.
l4_dest_port - Specifies the Layer 4 destination port ID for the match.
<value 1-65535> - Enter the Layer 4 destination port ID used here. This value must be
between 1 and 65535.
replace - Specifies to replace the outer-VLAN ID in the tag by the SVID. If there is no TAG in the
packet, this rule will not take effect.
svid - Specifies the S-VLAN ID to be assigned to the matched packet.
<vlanid 1-4094> - Enter the S-VLAN ID used here. This value must be between 1 and 4094.
priority - Specifies to assign the 802.1p priority of the S-Tag. If the priority is not specified, the
802.1p priority of S-Tag will be assigned by the default procedure.
<priority 0-7> - Enter the 802.1p priority value used here. This value must be between 0 and
7.
classify - Specifies the classification.
outer_vid - Specifies the packet’s outer-VID for the match.
<vlanid 1-4094> - Enter the packet's outer-VID used here. This value must be between 1 and
4094.
source_mac - Specifies the source MAC address or MAC address range for the match.
<macaddr> - Enter the source MAC address or range here.