
Operation
branches of a bush rubbing against it), all
proximity sensors are disabled for a certain
period of time.
Sensors will again be enabled:
●
After a time.
●
OR:
if the vehicle is unlocked with the but-
ton
on the key.
●
OR:
if the boot is opened.
●
OR:
if the vehicle is unlocked manually with
the key.
Keyless Access temporary disconnection
function*
You can deactivate the vehicle's Keyless
Access unlocking for one locking and un-
locking cycle.
●
Move the gear lever to position
P
(if the ve-
hicle has automatic gearbox), since other-
wise the vehicle cannot be locked.
●
Close the door.
●
Push the central locking button
on the
remote control and touch the locking sensor
surface of the driver door handle
within the following 5 seconds.
Do not grasp the door handle; otherwise the
vehicle will not unlock. Deactivation is also
possible if the vehicle is locked through the
driver’s door lock.
●
To check that the function has been deac-
tivated, wait at least 10 seconds, grip and pull
on the door handle. The door should not
open.
The next time the door can only be unlocked
via the remote control or the lock cylinder.
The next time the door is locked/unlocked,
Keyless Access will be active again.
Convenience functions
To close all the electric windows and the
sunroof using the
comfort function
, keep a
finger for a few seconds on the locking sen-
sor surface
B
(arrow) of the door
handle until the windows and roof have
closed.
How the
doors open
when touching the
sensor surface on the door handle will de-
pend on the settings that have been activa-
ted in the infotainment system, using the
button
> SETTINGS > Opening and
closing
.
CAUTION
The sensor surfaces on the door handles
could engage if hit with a water jet or high
pressure steam if there is a valid vehicle key
in the proximity. If at least one of the elec-
tric windows is open and the sensor surface
B
(arrow) on one of the handles is
activated continuously, all windows will
close.
Note
●
If the vehicle battery has little or no
charge, or the vehicle key battery is almost
or entirely out of charge, you will probably
not be able to lock or unlock the vehicle
with the Keyless Access system. The vehicle
can be unlocked or locked manually
●
To control the proper locking of the vehi-
cle, the release function is disabled for ap-
prox. 2 seconds.
●
If the message
Keyless access system
faulty
is displayed on the screen of the
dash panel, abnormalities may occur in the
operation of the Keyless Access system.
Contact a specialised workshop. To do so,
CUPRA recommends going to a specialised
CUPRA dealer or any SEAT dealership.
●
Depending on the function set on the in-
fotainment system for the mirrors, the ex-
terior mirrors will unfold and the surround
lighting will come on when unlocking the
vehicle using the sensor surface on the
driver and passenger door handles
●
If there is no valid key inside the vehicle
or the system fails to detect one, a warning
will display on the dash panel screen. This
could happen if any other radio frequency
signal interferes with the key signal (e.g.
from a mobile device accessory) or if the
key is covered by another object (e.g. an
aluminium case).
92
Summary of Contents for ATECA
