manualshive.com logo in svg

Cub Cadet Volunteer 4x4 Utility Vehicle, Shop Handbook, Page: 249 / 328

Share
Download
Cub Cadet Volunteer 4x4 Utility Vehicle Shop Handbook Download Page 249

Chapter 8 - Caterpillar Engine and Related Systems

245

5.

Cleaning the radiator (external)

5a.    The radiator should be visually checked for 

air blockage at the start of each operating 
day, while checking the coolant level.

5b.    If over-heating or general operating condi-

tion merits extra attention, check the con-
dition of the radiator before checking 
other components.

5c.    The radiator can be easily seen from the 

top and bottom for complete external 
inspection. 

CAUTION: 

If there is a possibility that the vehi-

cle has been operated in or exposed to hazard-
ous chemicals (such as pesticides), take 
appropriate precautions to prevent inhaling or 
ingesting those chemicals.

5d.     The radiator should self-clean through a 

combination of vibration and gravity, but 
may occasionally become blocked under 
extreme conditions.

5e.     Light dust may be cleared from the radia-

tor using compressed air regulated to 15 
PSI. (1.03 Bar).

CAUTION: 

  Wear eye protection and a dust 

mask (at minimum) when using compressed air 
to clean the radiator.  

CAUTION: 

Do not get the blow-gun close 

enough to the radiator core to dislodge or dam-
age the fins.  If the fins show any signs of dam-
age or distortion from the cleaning process stop 
cleaning immediately.

5f.      Heavier mud can be cleared using a water  

hose.  Use line head pressure only.  Do 
not pressure-wash the radiator.             
See Figure 8.67.

 

•

While the cooling fan motor is meant to work in 
an outdoor environment, it should be removed 
before washing the radiator.

•

If operating conditions are extremely dusty and 
the radiator has been washed, be sure it is thor-
oughly dry before returning it to the field.  In 
most cases this will happen as the engine 
warms-up.

•

Do not thermally shock the radiator by spraying 
water on it when it is hot.

CAUTION: 

  Wear eye protection (at minimum) 

when using water to clean the radiator.  

CAUTION: 

Do not get the hose nozzle close 

enough to the radiator core to dislodge or dam-
age the fins.  If the fins show any signs of dam-
age from the cleaning process stop cleaning 
immediately.

Figure 8.67

Mud accumulation from 
use in messy field conditions

Summary of Contents for Volunteer 4x4 Utility Vehicle









































































































































































































































































































































Reviews:

No comments