manualshive.com logo in svg

Cub Cadet Volunteer 4x4 Utility Vehicle, Shop Handbook, Page: 16 / 328

Share
Download
Cub Cadet Volunteer 4x4 Utility Vehicle Shop Handbook Download Page 16

Chapter 2- Drive System: CVT and Transfer Case

12

•

Slower idle speeds will result in poor idle quality, 
reduced flow of cooling air, and reduced oil flow.

•

Higher idle speeds will result in harsh gear 
selector action and possible internal damage to 
the transfer case.

2.

Top no-load speed should be 3,600 RPM for the 
Caterpillar and 3,850 RPM for the Kohler:           
See Figure 2.8.

•

Slower top no-load speeds will result in dimin-
ished performance.

•

Higher top no-load speeds will result in unsafe 
operating conditions and possible over-speed 
engine failure.

3.

If the idle speed and top-no-load speed do not 
fall into this range, refer to the appropriate 
engine chapter for adjustment procedures

•

Caterpillar related systems Chapter 8

•

Kohler engine service access and fuel system 
Chapter 7

DRIVE SYSTEM SERVICE ACCESS, SAFETY, AND 

TIPS                             

1.

When working on the belt, block the wheels to 
prevent the UV from rolling.

2.

Place the transmission in neutral.

3.

When working on any components (like the 
CVT) that rotate with the engine, disable the 
engine:

3a.    Disconnect and ground the spark plug 

wires on a gasoline engine. 

3b.     Unplug the fuel shut-off solenoid on a die-

sel engine.

3c.     Remove the key from the key switch.

3d.     Preferably, disconnect the ground cable 

from the negative terminal of the battery.

4.

Unless a procedure specifically requires the 
engine to be running, the engine should be 
turned-off for all maintenance, adjustments, and 
repair.

5.

To reach the CVT, fold the seats forward and 
secure them with shock cords.  Release the 
Camloc® fasteners and lift the parcel bin out 
from beneath the driver’s seat 

6.

Once accessed, the driving element, the driven 
element, and the belt can be removed.  There 
are some simple but 

specialized tools

 required 

to loosen the belt and remove the driving ele-
ment

•

A 

small screw

 can be used to spread the 

sheaves of the driven element so that the belt 
can be removed.  Specific dimensions are given 
in the belt removal section of this chapter.

•

A 

clutch puller

 is needed to pull the driving ele-

ment off of the tapered crankshaft.

NOTE: 

The belt may be removed independently, 

or the CVT may be removed complete with the 
belt.

Figure 2.8

Belt spinning

Sheaves
closed

Engine at
max. RPM

Summary of Contents for Volunteer 4x4 Utility Vehicle









































































































































































































































































































































Reviews:

No comments